Ich habe ein Telefon mit 2.3 und ein Tablet mit 3.1 im drahtlosen Netzwerk zusammen mit einer Reihe von Computern. Ich habe ein bisschen ein Netzwerk-Geheimnis.
Hier die Fakten:
am telefon sehe ich nur eine route zum lokalen netz und ein defaultgateway
ip address:
... many rmnet addresses ...
eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdic pfifo_fast static UP plen 1000
inet/ether 64:a7:69:70:76:7b brd ff:ff:ff:ff:ff:ff
inet 192.168.11.4/24 brd 192.168.11.255 scope global eth0
inet <link local ip6>
auf dem Tablett:
# ip r
192.168.11.1 dev wlan0 scope link
192.168.11.0/24 dev wlan0 proto kernel scope link src 192.168.11.6 metric 306
default via 192.168.11.1 dev wlan0
default via 192.168.11.1 dev wlan0 metric 306
#
#
# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN
link/ether 42:cf:a5:fd:26:81 brd ff:ff:ff:ff:ff:ff
3: usb0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
link/ether 1e:2e:a2:c3:16:7e brd ff:ff:ff:ff:ff:ff
4: sit0: <NOARP> mtu 1480 qdisc noop state DOWN
link/sit 0.0.0.0 brd 0.0.0.0
5: ip6tnl0: <NOARP> mtu 1460 qdisc noop state DOWN
link/tunnel6 :: brd ::
6: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
link/ether f4:6d:04:39:26:21 brd ff:ff:ff:ff:ff:ff
inet 192.168.11.6/24 brd 192.168.11.255 scope global wlan0
inet6 fe80::f66d:4ff:fe39:2621/64 scope link
valid_lft forever preferred_lft forever
Auch auf dem Tablet sehe ich, dass das Problem darin besteht, dass ARP-Anforderungen fehlschlagen:
# ping 192.168.11.100
PING 192.168.11.100 (192.168.11.100) 56(84) bytes of data.
From 192.168.11.3 icmp_seq=2 Destination Host Unreachable
From 192.168.11.3 icmp_seq=3 Destination Host Unreachable
From 192.168.11.3 icmp_seq=4 Destination Host Unreachable
^C
--- 192.168.11.100 ping statistics ---
5 packets transmitted, 0 received, +3 errors, 100% packet loss, time 4005ms, pipe 3
# ip neighbor show
192.168.11.100 dev wlan0 FAILED
192.168.11.1 dev wlan0 lladdr 00:16:01:a1:a4:18 STALE
#
brach den Paket-Sniffer aus und stellte fest, dass Broadcast-Arp-Anforderungen von Android-Geräten im Access Point abgelegt wurden.
stellte sich als Fehler bei meinem Buffalo 300n Wireless Access Point heraus. Billiger neuer AP und Problem weg...anscheinend sprechen einige APs einfach nicht mit Android?
gelöst durch das Prinzip "das billigste zuerst ersetzen"
Artur Ulfeldt
Matthäus Lesen
TomG
Artur Ulfeldt