Ich versuche, einen detaillierten SMART-Statusbericht über die Laufwerke in meinem Mac zu erhalten. Ich spreche nicht von „Verifiziert“, ich spreche von dem detaillierten Bericht, der etwa 100 Zeilen lang ist und alle wichtigen Statistiken des Laufwerks auflistet.
Weiß jemand, wie man das mit diskutil macht? Wenn diskutil dies nicht kann, gibt es ein anderes kostenloses Tool, das ich verwenden kann?
Ich hatte kürzlich die gleiche Frage und fand ein Kommandozeilentool www.smartmontools.org , das über brew installiert werden kann:
brew install smartmontools
Auch über MacPorts:
sudo port install smartmontools
dann kannst du es ausführen
smartctl -a disk0s3
Für den vollständigen Bericht, wo disk0s3
sich die physische Sicherung der Festplatte befindet, finden Sie sie in Disk Utility.app, indem Sie Informationen zum Laufwerk abrufen. (oder über diskutil list
die Befehlszeile.) Hier ist ein Beispiel für die Ausgabe:
smartctl 6.2 2013-07-26 r3841 [x86_64-apple-darwin13.1.0] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Samsung based SSDs
Device Model: Samsung SSD 840 Series
Serial Number: S14LNEAD609248A
LU WWN Device Id: 5 002538 5503acd2e
Firmware Version: DXT08B0Q
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Thu Jun 19 16:34:10 2014 MDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (53956) seconds.
Offline data collection
capabilities: (0x53) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 70) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 2379
12 Power_Cycle_Count 0x0032 098 098 000 Old_age Always - 1579
177 Wear_Leveling_Count 0x0013 096 096 000 Pre-fail Always - 38
179 Used_Rsvd_Blk_Cnt_Tot 0x0013 100 100 010 Pre-fail Always - 0
181 Program_Fail_Cnt_Total 0x0032 100 100 010 Old_age Always - 0
182 Erase_Fail_Count_Total 0x0032 100 100 010 Old_age Always - 0
183 Runtime_Bad_Block 0x0013 100 100 010 Pre-fail Always - 0
187 Uncorrectable_Error_Cnt 0x0032 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0032 059 039 000 Old_age Always - 41
195 ECC_Error_Rate 0x001a 200 200 000 Old_age Always - 0
199 CRC_Error_Count 0x003e 100 100 000 Old_age Always - 0
235 POR_Recovery_Count 0x0012 099 099 000 Old_age Always - 1571
241 Total_LBAs_Written 0x0032 099 099 000 Old_age Always - 14090964124
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
255 0 65535 Read_scanning was never started
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
-l devstat /dev/disk1
) abzurufen, aber ich erhalte diesen Fehler:ATA_READ_LOG_EXT (addr=0x00:0x00, page=0, n=1) failed: 48-bit ATA commands not implemented. ... Device Statistics (GP/SMART Log 0x04) not supported
Hier sind zwei zusätzliche Wissensklumpen, die hilfreich sein können:
das smartmontools
Paket ist auch unter MacPorts verfügbar. Wenn Sie MacPorts installiert haben, reicht sudo port install smartmontools
es aus
Der df
Befehl gibt Ihnen schnell eine Vorstellung davon, was wo montiert ist.
smartctl
... sagt "Befehl nicht gefunden" ... auch nach dem Ausführen sudo port load smartmontools
und Neustarten des Computers ... irgendwelche Ideen?Als Erweiterung der hervorragenden Antwort von Lee Joramo können Sie die GSmartControl- GUI über smartmontools
. Es kommt in einem Homebrew-Zapfhahn.
Das Verfahren ist also:
brew install smartmontools
brew install gsmartcontrol
gsmartcontrol
Oder, wenn Sie MacPorts verwenden:
sudo port install gsmartcontrol
(wird automatisch smartmontools
als Abhängigkeit installiert)
Übrigens: Ich musste SMART erst aktivieren. Die GUI kann das für Sie erledigen. Wenn Sie die Befehlszeile verwenden möchten, ist es smartctl -s on -a disk0s2
.
gsmartcontrol
(mit unzähligen Abhängigkeiten) mit Macports installiert, aber beim Ausführen gsmartcontrol
wird eine Gtk-Warnung angezeigt, dass die Anzeige nicht geöffnet werden kann. Was wird noch benötigt?Ganz neu und kompatibel mit MacOS Sierra, Yosemite und El Capitan Option:
Holen Sie sich das native vorkompilierte Paket von https://sourceforge.net/projects/smartmontools/
Installieren Sie es, öffnen Sie das Terminal und führen Sie Folgendes aus:
sudo /usr/local/sbin/smartctl -a /dev/disk0
Sie erhalten eine vollständige Ausgabe wie folgt:
smartctl 6.5 2016-05-07 r4318 [Darwin 16.3.0 x86_64] (sf-6.5-1)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Crucial/Micron MX100/MX200/M5x0/M600 Client SSDs
Device Model: Crucial_CT500MX200SSD1
Serial Number: 16151248FBA4
...
ATA Version is: ACS-3 T13/2161-D revision 4
SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s)
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
...
und den folgenden Rest der SMART-Informationen. Ich hoffe, dies hilft Benutzern, die eine einfache Lösung wünschen.
Einige zusätzliche Informationen zur Ausführung von smartctl 7.1 auf macOS 10.15 (Catalina)+
Verhalten/Ausgabe variiert, wenn SSD-Typen unterschiedlich sind, z. B. NVMe vs. SATA/SATA Express
MacBookPro14,3 (NVMe) 512GB SM0512L
kann smartctl
tatsächlich ein Feld mit dem Namen abrufen, Data Units Written
das äquivalent zu ist Total LBAs Written
.
Link Width: x4
Link Speed: 8.0 GT/s
# smartctl output
smartctl -a /dev/disk0
smartctl 7.1 2019-12-30 r5022 [Darwin 19.5.0 x86_64] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Number: APPLE SSD SM0512L
Serial Number: C0281xxxxxxxx2
Firmware Version: CXS5EA0Q
PCI Vendor/Subsystem ID: 0x144d
IEEE OUI Identifier: 0x002538
Controller ID: 2
Number of Namespaces: 1
Local Time is: Thu Jul 2 12:05:31 2020 AEST
Firmware Updates (0x06): 3 Slots
Optional Admin Commands (0x0006): Format Frmw_DL
Optional NVM Commands (0x001f): Comp Wr_Unc DS_Mngmt Wr_Zero Sav/Sel_Feat
Maximum Data Transfer Size: 256 Pages
Supported Power States
St Op Max Active Idle RL RT WL WT Ent_Lat Ex_Lat
0 + 6.00W - - 0 0 0 0 5 5
1 - 0.0400W - - 1 1 1 1 210 1200
2 - 0.0050W - - 2 2 2 2 1900 5300
=== START OF SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
SMART/Health Information (NVMe Log 0x02)
Critical Warning: 0x00
Temperature: 35 Celsius
Available Spare: 100%
Available Spare Threshold: 10%
Percentage Used: 1%
Data Units Read: 45,208,642 [23.1 TB]
Data Units Written: 44,739,539 [22.9 TB]
Host Read Commands: 1,440,047,433
Host Write Commands: 833,678,921
Controller Busy Time: 1,952
Power Cycles: 7,356
Power On Hours: 1,190
Unsafe Shutdowns: 47
Media and Data Integrity Errors: 0
Error Information Log Entries: 0
Read Error Information Log failed: NVMe admin command:0x02/page:0x01 is not supported
(Mitte 2015) MacBookPro 11,5 (unter SATA/SATA Express, aber immer noch PCIe-basierte SSD) 512 GBSM0512G
175 Host_Writes_MiB
ist der Schlüssel.
terrywang@ninja:~$ smartctl -a /dev/disk0
smartctl 7.1 2019-12-30 r5022 [Darwin 19.5.0 x86_64] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Apple SD/SM/TS...E/F/G SSDs
Device Model: APPLE SSD SM0512G
Serial Number: S------------63
LU WWN Device Id: 5 002538 900000000
Firmware Version: BXW1SA0Q
User Capacity: 500,277,790,720 bytes [500 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: Solid State Device
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4c
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Thu Jul 2 12:17:35 2020 AEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x53) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 10) minutes.
SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x001a 200 200 000 Old_age Always - 0
5 Reallocated_Sector_Ct 0x0033 100 100 000 Pre-fail Always - 0
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 5303
12 Power_Cycle_Count 0x0032 067 067 000 Old_age Always - 32789
169 Unknown_Apple_Attrib 0x0013 239 239 010 Pre-fail Always - 3629423527808
173 Wear_Leveling_Count 0x0032 196 196 100 Old_age Always - 21484011576
174 Host_Reads_MiB 0x0022 099 099 000 Old_age Always - 26175030
175 Host_Writes_MiB 0x0022 099 099 000 Old_age Always - 19170887
192 Power-Off_Retract_Count 0x0012 099 099 000 Old_age Always - 48
194 Temperature_Celsius 0x0022 073 018 000 Old_age Always - 27 (Min/Max 9/82)
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
199 UDMA_CRC_Error_Count 0x001a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Warning! SMART Selective Self-Test Log Structure error: invalid SMART checksum.
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
255 0 65535 Read_scanning was never started
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Samsung Magician verwendet einfach die TBW einer SSD als Gesundheitsindikator, z. B. 850 EVO 250 GB (entworfene TBW 75 GB).
2,56 TB / 75 TB = 3,41 % der vorgesehenen Kapazität.
HINWEIS: Unter Linux (oder Windows) ist SMART - ID 241
Total LBAs Written
diejenige, die Sie sich ansehen sollten, aber bitte beachten Sie, dass sie die Anzahl der 512-Byte-Sektoren meldet, Sie müssen rechnen, um sie in TB oder TiB umzuwandeln.
Formel: (Total_LBAs_Written * Sektorgröße) / 1024^4 = TiB Konvertiere TiB in TB (Facepalm) / TBW -> % geplante Lebensdauer
Die meisten MacOS unterstützen SMART nicht und wenn Sie versuchen, ein MacART-Attribut anzuwenden, schlägt die Installation fehl und das System friert nach jeder durchgeführten Aktion ein, wie z. B. dem Kopieren einer Datei, und am Ende des Vorgangs wird das Betriebssystem gesperrt . Dies liegt daran, dass SMART die Daten in dem Moment, in dem die Datei abgelegt wird, auf dem Laufwerk ein- und ausliest. Die SMART-Sensoren bewirken, dass das System einfriert, da es auf einem überwachten System nicht unterstützt wird. Es wird nicht unterstützt. Wenn Sie SMART auf einem Mac oder Mac OS aktiviert haben, gehen Sie in das Festplattendienstprogramm und unten in den Festplatteninformationen sehen Sie, dass SMART nicht unterstützt wird. Die meisten MacOS, die ich kenne, unterstützen diese Funktion nicht, und um einen Hackintosh dazu zu bringen, die meisten Distributions-Installer zu installieren, ohne dass Ihr System abgelehnt wird, dürfen Sie diese Funktion nicht aktivieren. Ich habe sogar Linux Mint in Virtualbox auf einem RAM-Laufwerk installiert und sage, dass es SMART nicht unterstützt. Ich werde ein paar Bilder posten. Jede Festplatte, die diese Funktion hat, funktioniert nicht sehr gut mit MacOS.
Sie können ziemlich viele Informationen von der kostenlosen Version von SmartReporter erhalten: https://www.corecode.io/smartreporter_lite/
Drop in Utilities und doppelklicken Sie darauf. Klicken Sie auf das Symbol in der Leiste oben auf dem Bildschirm. Klicken Sie in den Einstellungen mit der rechten Maustaste auf eine Festplatte und spielen Sie mit den Optionen.
Hier ist eine vollständige Anleitung zu smartmontools unter osx , einschließlich wo man es findet, wie man es installiert und wie man es benutzt, vom Autor Benjamin von der Weiden.
BIP2
OS-X-SAT-SMART-Driver
undDriveDx
), sind diesbezüglich derzeit beide defekt. Ersteres befindet sich nicht mehr in der aktiven Entwicklung, undDriveDx
Sie müssen Ihr Gerät trennen / neu anschließen, damit es funktioniert.Gilby
DriveDX
teilweise nicht mehr kaputt.